The right generator size depends on what you want to power during an outage, not only on how big your home is. A generator that is too small trips its breaker when motors start. One that is too large wastes money and fuel.
This guide shows you how to size a home generator in Canada. You will find typical kW ranges by house size, a wattage chart for common appliances, and four steps to add up running watts and starting watts. It also compares standby, portable, and inverter generators, explains why you need a transfer switch, and covers cold-weather needs. That way your furnace fan, sump pump, and fridge keep running through a winter power outage.
Quick Answer: Generator Size by Home Type
Most Canadian homes need a 13 to 20 kW standby generator for full backup. A smaller 3 to 13 kW unit covers essentials only: the fridge, furnace fan, sump pump, lights, and internet. Large homes with central air or a heat pump need 22 kW or more.
|
Home type |
Typical generator size |
What it covers |
|
Essentials only |
3 to 7.5 kW portable, or 7 to 13 kW standby |
Fridge, furnace fan, lights, sump pump, internet |
|
Mid-size home (1,500 to 2,500 sq. ft.) |
13 to 22 kW standby |
Most circuits, with load management for AC |
|
Large home (3,000+ sq. ft.) |
22 to 30 kW standby |
Most circuits, central air, kitchen |
|
Whole-home, all-electric or with EV |
26 to 48 kW standby |
Electric heat, central air, EV charger, range, dryer |
These are planning ranges. A licensed electrician should confirm the final number.
Generator Size by House Size (Square Footage)
Square footage gives a starting point. The ranges below assume gas heat unless noted.
Small Homes and Condos
Homes under 1,500 sq. ft. usually need 3 to 10 kW. A 10 kW standby unit covers essential circuits, lights, refrigeration, and small appliances. Condo bylaws often limit standby units and fuel storage, so many owners choose a portable or inverter generator with a transfer switch. Check your bylaws before you buy.
Average Family Homes (1,500-2,500 sq. ft.)
Plan on 13 to 22 kW. At about 1,550 sq. ft., Generac suggests 10 to 18 kW, depending on central air and a well pump. At 2,000 sq. ft., a 20 to 22 kW unit covers whole-home loads. With load management, a mid-size unit can cover more circuits.
Large Homes (3,000+ sq. ft.)
Large homes usually need 22 to 30 kW. Generac treats 22 kW as the standard for homes of 2,500 to 3,000 sq. ft. Homes with two HVAC zones, a pool pump, or a workshop may need a liquid-cooled unit of 25 kW or more.
Why Square Footage Alone Isn't Enough
Two homes of the same size can differ by 8 kW or more. A 1,550 sq. ft. home with gas heat and city water draws far less than one with a heat pump and a well pump. Heating fuel, motors that start together, and your backup goals matter more than floor area.
How to Calculate the Generator Size Your House Needs
Four steps give you a reliable number.
Step 1: List the Appliances and Circuits You Want to Power
Write down everything you need during an outage. Sort it into three groups:
-
Essentials: fridge, freezer, router, LED lights, sump pump
-
Comforts: microwave, garage door opener
-
Heavy hitters: central air, electric range, well pump, EV charger, dryer
Decide whether you want essential circuits only or the whole house.
Step 2: Find Running Watts and Starting (Surge) Watts
Running watts are what a device draws once it is on. Starting watts are the burst a motor needs to start, often two to three times higher. Check the nameplate, owner's manual, or spec sheet. Furnace fans, sump pumps, well pumps, fridges, and AC units have the biggest surges.
Step 3: Add Up Your Total Load
Add all running watts. Then add the largest single starting surge, because motors rarely all start at the same moment.
Total watts = sum of running watts + highest starting surge
Divide by 1,000 to get kW.
Step 4: Add a Safety Margin
Add 20% to 30% to your total. The margin covers aging motors, cold starts, and loads you add later.
Watts, kW, and kVA Explained (Amps × Volts = Watts)
Watts equal amps times volts. A 20 A appliance on 240 V draws 4,800 W. One kW equals 1,000 W. The unit kVA measures apparent power. kW equals kVA times the power factor, which is often 0.8 on larger units. Most Canadian homes run on 120/240 V single-phase power, so compare kW ratings.
Generator Wattage Chart for Common Household Appliances
Motor-driven appliances need the most attention because of their surge. The table below covers all three groups.
Kitchen Appliances
Fridges and freezers have small running loads but a sharp start surge. Microwaves and electric ranges draw the most. During an outage, you can cook one item at a time to keep the total low.
Heating, Cooling, and Water Systems (Furnace Fan, Heat Pump, Well Pump, Sump Pump, Water Heater)
A gas furnace fan is a modest load. Central air, heat pumps, and electric water heaters are the largest. Well pumps and sump pumps have high surges for their size. Soft-start kits can cut the AC surge by about half.
Lights, Electronics, and Internet
These loads are small. LED lights, a router, a laptop, and a TV together draw a few hundred watts. They add little to your total, so cover them first.
|
Appliance |
Running watts |
Starting watts |
|
Refrigerator |
100 to 200 |
600 to 1,200 |
|
Chest freezer |
100 to 150 |
500 to 1,000 |
|
Microwave |
1,000 to 1,500 |
1,000 to 1,500 |
|
Coffee maker |
600 to 1,200 |
600 to 1,200 |
|
Electric range (burners and oven) |
3,000 to 5,000 |
3,000 to 5,000 |
|
Furnace fan (gas furnace) |
400 to 800 |
1,200 to 2,400 |
|
Central AC or heat pump (3-ton) |
3,500 to 5,000 |
Up to 15,000 to 18,000 |
|
Well pump (1/2 hp) |
1,000 |
2,100 |
|
Sump pump (1/3 hp) |
800 to 1,000 |
1,300 to 2,150 |
|
Electric water heater |
4,000 to 4,500 |
4,000 to 4,500 |
|
Electric dryer |
3,000 to 5,000 |
3,000 to 5,000 |
|
LED bulb |
5 to 15 |
5 to 15 |
|
Wi-Fi router and modem |
10 to 30 |
10 to 30 |
|
TV |
100 to 400 |
100 to 400 |
|
Laptop |
50 to 100 |
50 to 100 |
|
Garage door opener |
350 to 500 |
750 to 1,400 |
|
EV charger (Level 2) |
7,200 |
7,200 |
Figures are typical values. Your nameplate gives the exact numbers.
Essential-Load vs Whole-House Generator Sizing
This choice is often the biggest driver of generator size.
Backing Up Essential Circuits Only
Essential backup powers the fridge, furnace fan, sump pump, lights, and a few outlets, usually through a backup loads panel. It needs about 3 to 13 kW. It costs less to buy and burns less fuel. It suits homes with gas heat and shorter outages.
Powering the Whole House
Whole-house backup runs HVAC, the kitchen, laundry, and the water heater. It usually needs 22 kW or more. It suits all-electric homes, rural homes with well pumps, and areas with long winter outages.
Load Management and Smart Panels to Reduce Generator Size
A load manager pauses low-priority loads, such as a dryer or AC, when the generator nears its limit. Generac says this lets you cover more circuits with a smaller unit. Smart panels do the same circuit by circuit. You no longer size for every device running at the same second.
Standby vs Portable vs Inverter: Which Type Fits Your Size Needs?
Portable Generators
Portable units usually range from 3,000 to 10,000 W. They run on gasoline or propane and start by hand. Most homeowners connect them through an interlock kit or inlet box. They suit essentials and short outages. Run them outdoors only, well away from windows and doors, because of carbon monoxide.
Inverter and Dual Fuel Generators
Inverter generators produce clean power, which protects laptops, routers, and medical devices. They are quiet but usually top out near 4,000 W. Dual fuel models switch between gasoline and propane and often reach about 12,000 W. These fit small homes and condos.
Standby (Whole-Home) Generators
Standby units sit outside on a pad and connect to natural gas or propane. They start within seconds through an automatic transfer switch. Generac air-cooled models range from 10 to 28 kW. Cummins QuietConnect air-cooled models run 13 to 20 kW, and liquid-cooled models start at 25 kW. Cummins QuietConnect units run at 65 dB or less at 7 metres. Browse the Generac and Cummins standby generators at Volts Énergies to compare kW ratings by size.
Factors That Change the Generator Size You Need
The generator size your home needs depends on your heating system, electrical capacity, major appliances, winter conditions, and fuel availability.
Electric vs Gas/Propane/Oil Heating
A gas, propane, or oil furnace needs only a fan, about 400 to 800 W. Electric furnaces and baseboards can draw 5,000 to 25,000 W. Electric heat usually pushes you toward a large standby unit.
Electrical Panel Size (100A vs 200A Service)
Panel size sets the ceiling, not the target. A 100 A service tops out at 24 kW (100 × 240). A 200 A service tops out at 48 kW. Most homes use far less. Match the transfer switch rating to your service.
Central Air, Heat Pumps, and Electric Vehicle Charging
A 3-ton central AC runs at 3,500 to 5,000 W but can surge to 15,000 W or more. A Level 2 EV charger adds 7,200 W. Soft-start kits and load management keep these from forcing a larger unit.
Cold Climate and Canadian Winter Conditions
Winter outages often come with ice storms and last for days. Heat pumps and electric heat run longer in January. Engines need cold-weather support, such as battery warmers and block heaters, to start at -30°C. Check the manufacturer's cold rating, and keep snow clear of the unit.
Fuel Type and Runtime
Natural gas supplies fuel without refilling. Propane runs from a tank, so size the tank for several days. Gasoline portables need refuelling every 8 to 12 hours at half load. Fuel use rises with load, so right-sizing also cuts running cost.
Considering these factors helps you choose a generator that handles essential loads, manages peak demand, and delivers reliable backup power during Canadian winters.
What Happens If Your Generator Is Too Small or Too Big?
Choosing the wrong generator size can lead to power interruptions, unnecessary fuel consumption, and higher costs, making accurate load calculations essential.
Undersized Generator: Overloads and Shutdowns
An undersized generator trips its breaker or stalls when motors start. Voltage and frequency dips can damage motors and electronics. The furnace fan or sump pump may fail to start when you need it most.
Oversized Generator: Wasted Cost and Fuel
An oversized generator costs more to buy and install. It needs a larger pad and gas line. It also runs at light loads, which wastes fuel. Generac notes that oversizing means overpaying at purchase and every time the unit runs.
Generator Sizing Examples
Essential Backup Example (Fridge, Furnace Fan, Lights, Sump Pump, Internet)
-
Running watts: fridge 150 + furnace fan 800 + lights 100 + sump pump 800 + internet 20 = 1,870 W
-
Largest surge: furnace fan at 2,400 W
-
Total: 1,870 + 2,400 = 4,270 W
-
With a 25% margin: about 5,340 W
A 6,500 to 7,500 W portable with an interlock kit works, or a 7 to 10 kW standby unit.
Mid-Size Home Example
A 2,000 sq. ft. home with gas heat and a 3-ton AC:
-
Running watts: fridge 150 + furnace fan 800 + lights 300 + sump pump 800 + electronics 400 + microwave 1,200 + AC 4,000 = 7,650 W
-
Without a soft start, the AC surge is 15,000 W. The total reaches 22,650 W, or 28,300 W with margin.
-
With a soft-start kit that cuts the surge to about 7,000 W, the total is 14,650 W, or about 18,300 W with margin.
An 18 to 22 kW standby unit fits.
Whole-Home Example
A 3,000 sq. ft. home with an electric range, dryer, electric water heater, 4-ton AC, and well pump reaches about 23,850 W running if everything runs at once. Unmanaged setups like this often need 26 to 30 kW. A load manager that holds the dryer, range, and water heater to one at a time drops the running peak to about 15,350 W. A 22 kW unit then leaves room for motor surges.
Do You Need an Electrician or Transfer Switch to Size and Install a Generator?
Yes, for any generator that connects to your home. A licensed electrician measures your panel loads, confirms the size, and pulls the permit. Standby units also need a licensed gas fitter. Installs must follow the Canadian Electrical Code and local rules.
A transfer switch isolates your home from the grid. This stops power from flowing back to the lines and protects utility workers. Automatic transfer switches (ATS) start the generator on their own. Manual switches and interlock kits suit portable units. Never plug a generator into a wall outlet. Volts Énergies stocks Cummins RSS and RA series transfer switches for complete installations.
If you want silent backup instead of a generator, read our home battery storage cost guide to compare the two.
Final Thoughts
Generator size comes down to what you want to run, not how big your home is. List your essential loads, find the running and starting watts, add a 20% to 30% margin, and decide between essential circuits and whole-home backup. Most Canadian homes land between 13 and 20 kW for standby power. Have a licensed electrician confirm the load before you buy, and install a transfer switch to keep your home and utility workers safe.
FAQs
What Size Generator Do I Need To Run A Whole House?
Most homes need 13 to 20 kW. A 22 kW unit is the usual choice for 2,500 to 3,000 sq. ft. Large or all-electric homes may need 26 kW or more, unless load management limits the peak.
Will A 5,000-Watt Generator Run A House?
It can run essentials, not the whole house. A 5,000 W unit covers a fridge, furnace fan, lights, sump pump, and internet. It cannot run central air, an electric range, or a dryer.
What Size Generator Do I Need For A 2,000 Sq. Ft. House?
For whole-home coverage, plan on 18 to 22 kW. For essentials only, 7 to 13 kW is enough. Central air, a well pump, and electric heat push the size higher.
What Size Generator Do I Need To Run A Furnace?
A gas furnace fan needs 400 to 800 W running and up to 2,400 W to start. A 3,000 to 5,000 W portable covers it. Electric furnaces draw 5,000 to 25,000 W and need a large standby unit.
Can I Run A House On A Portable Generator?
Yes, for essentials. A portable with a transfer switch or interlock kit can power key circuits. It needs manual starting, regular refuelling, and outdoor use only. Standby units suit long outages better.
Is A 20 Kw Generator Enough For A Whole House?
For most homes of 2,000 to 2,500 sq. ft. with gas heat, yes. It may fall short for all-electric homes or homes with an EV charger, unless load management controls the peak.
How Do I Find My Generator's Starting Watts?
Check the appliance nameplate, owner's manual, or spec sheet. If it is not listed, multiply the running watts by two to three for motors. For AC units, locked rotor amps times volts gives a close figure.
What Size Generator Do I Need For Central Air Conditioning?
A 3-ton unit runs at 3,500 to 5,000 W but can surge to 15,000 to 18,000 W. With a soft-start kit or load manager, a 14 to 18 kW generator often handles it.
What Size Generator Do I Need For A Well Pump?
A 1/2 hp well pump runs at about 1,000 W and starts at about 2,100 W. A 3,000 to 5,000 W portable can handle one. Larger pumps need more, so check the nameplate.
Do I Need A Permit To Install A Standby Generator?
Usually yes. Most areas require an electrical permit and a gas permit, plus an inspection. Local bylaws may also set setbacks and noise limits. Your installer should handle the filings.
Find the Right Generator Size with Volts Energies
Not sure which kW rating fits your home? Volts Énergies carries Generac, Cummins, and Winco generators, plus transfer switches. Browse the generators collection to compare sizes, or contact our team to match a unit to your load.